FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
current that can result in an undesired voltage spike once the
capacitor is fully charged. The soft start is active each time
the IC goes out of standby or shutdown mode, power is
recycled, or after a fault retry.
After a successful start-up cycle where the device is
enabled, no faults have occurred, and the output voltage has
reached its regulation point, the 34717 pulls the power good
output signal low after a 10 ms reset delay, to indicate to the
host that the device is in normal operation.
PROTECTION FUNCTIONS
The 34717 monitors the application for several fault
conditions to protect the load from overstress. The reaction of
the IC to these faults ranges from turning off the outputs to
just alerting the host that something is wrong. In the following
paragraphs, each fault condition is explained:
Output Over-voltage
An over-voltage condition occurs once the output voltage
goes higher than the rising over-voltage threshold (V OVR ). In
this case, the power good output signal is pulled high, alerting
the host that a fault is present, but the output will stay active.
To avoid erroneous over-voltage conditions, a 20 μs filter is
implemented. The buck converter will use its feedback loop
to attempt to correct the fault. Once the output voltage falls
below the falling over-voltage threshold (V OVF ), the fault is
cleared and the power good output signal is pulled low, the
device is back in normal operation.
Output Under-voltage
An under-voltage condition occurs once the output voltage
falls below the falling under-voltage threshold (V UVF ). In this
case, the power good output signal is pulled high, alerting the
host that a fault is present, but the output will stay active. To
avoid erroneous under-voltage conditions, a 20 μs filter is
implemented. The buck converter will use its feedback loop
to attempt to correct the fault. Once the output voltage rises
above the rising under-voltage threshold (V UVR ), the fault is
cleared and the power good output signal is pulled low, the
device is back in normal operation.
Output Over-current
This block detects over-current in the Power MOSFETs of
the buck converter. It is comprised of a sense MOSFET and
detecting device by sampling a ratio of the load current. That
sample is compared via the comparator with an internal
reference to determine if the output is in over-current or not.
If the peak current in the output inductor reaches the over
current limit (I LIM ), the converter will start a cycle-by-cycle
operation to limit the current, and a 10 ms over-current limit
timer (t LIM ) starts. The converter will stay in this mode of
operation until one of the following occurs:
? The current is reduced back to the normal level before
t LIM expires, and in this case normal operation is
regained.
? t LIM expires without regaining normal operation, at
which point the device turns off the output and the
power good output signal is pulled high. At the end of a
time-out period of 100 ms (t TIMEOUT ), the device will
attempt another soft start cycle.
? The device reaches the thermal shutdown limit (T SDFET )
and turns off the output. The power good output signal
is pulled high.
? The output current keeps increasing until it reaches the
short-circuit current limit (I SHORT ). See below for more
details.
Short-circuit Current Limit
This block uses the same current detection mechanism as
the over-current limit detection block. If the load current
reaches the I SHORT value, the device reacts by shutting down
the output immediately. This is necessary to prevent damage
in case of a permanent short circuit. Then, at the end of a
timeout period of 100 ms (t TIMEOUT ), the device will attempt
another soft start cycle.
Thermal Shutdown
Thermal limit detection block monitors the temperature of
the device and protects against excessive heating. If the
temperature reaches the thermal shutdown threshold
(T SDFET ), the converter output switches off and the power
good output signal indicates a fault by pulling high. The
device will stay in this state until the temperature has
decreased by the hysteresis value and then After a timeout
period (t TIMEOUT ) of 100 ms, the device will retry
automatically and the output will go through a soft start cycle.
If successful normal operation is regained, the power good
output signal is asserted low to indicate it.
a comparator. The sense MOSFET acts as a current
34717
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
相关PDF资料
KS-1787-MG SHELF SLIDING KEYBOARD ASSEMBLY
KS-1788 SHELF SLIDING KEYBOARD ASSEMBLY
KSDKSTM32-PL KIT IAR KICKSTART STM32 CORTEXM3
LC4064ZC-EV BOARD EVAL FOR ISPMACH 4064ZC
LCMXO2280C-C-EVN BOARD CONTROL EVAL MACHXO
LDB100-024SW LED POWER SUPPLY 24V 0-4A 100W
LDB150-048SW LED POWER SUPPLY 24V-48V 3.125A
LDB200-048SW LED POWER SUPPLY 24V-48V 4.2A
相关代理商/技术参数
KIT34727FCEVBE 功能描述:电源管理IC开发工具 600MA HIGH EFFICIENCY LO RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
KIT34825EPEVME 功能描述:界面开发工具 MICRO USB INTERFACE IC RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V
KIT34844AEPEVBE 功能描述:LED 照明开发工具 IC, 10 CHANNEL LED BACKLIGHT RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装:
KIT34844EPEVME 功能描述:LED 照明开发工具 MC34844 10-Ch LED BL Driver Eval Kit RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装:
KIT34845EPEVME 功能描述:LED 照明开发工具 IC, 6 CHANNEL LED BACKL RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装:
KIT34929EPEVME 功能描述:电源管理IC开发工具 1.0 A/ 28 V BRUSHLESS DC RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
KIT3500UZ 功能描述:KIT CAP CERM HI FREQ 1210 RoHS:是 类别:套件 >> 无源 - 电容器 系列:U 标准包装:1 系列:SP-Cap CD, CX, SL, SX 套件类型:聚合物,铝电解 值:135 件 - 39µF ~ 470µF,各 15 件 包装:- 安装类型:表面贴装 包括封装:7343-17,7343-20 产品目录页面:2651 (CN2011-ZH PDF) 工具箱内容:(15) PCE4991CT-ND - CAP ALUM 220UF 4V 20% SMD(15) PCE4990CT-ND - CAP ALUM 330UF 2V 20% SMD(15) PCE4989CT-ND - CAP ALUM 150UF 6.3V 20% SMD(15) PCE4988CT-ND - CAP ALUM 150UF 6.3V 20% SMD(15) PCE4943CT-ND - CAP ALUM 39UF 10V 20% SMD(15) PCE4823CT-ND - CAP ALUM 470UF 2V 20% SMD(15) PCE4816CT-ND - CAP ALUM 220UF 4V 20% SMD(15) PCE4479CT-ND - CAP ALUM 220UF 2V 20% SMD(15) PCE4472CT-ND - CAP ALUM 120UF 2V 20% SMD 其它名称:SP4-KIT
KIT35XS3400EVBE 功能描述:交换机 IC 开发工具 QUAD HI SIDE SWITCH RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:USB Power Switches 工具用于评估:MAX4984E 工作电源电压:2.8 V to 5.5 V